Innotech Genesis II Digital Controller (v5) User Manual Page 63
- Page / 124
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Page 63
Genesis II Installation Instructions
© Mass Electronics Pty Ltd 2010Chapter 3 – Electrical Installation
END OF
CABLE
JUMPER
RS485
COMMS
CONNECTIONS
POWER
3-4.13 GENII CSFCAH REM Control Station Fan Control A/H Module
The GENII CSFCAH REM Control Station Fan Control, A/H Module is powered by 24VAC ±10% @ 50/60
Hz. Power Consumption is 3VA maximum.
The GENII CSFCAH REM mounts into a standard electrical wall plate. The only connections to the
GENII CSFCAH REM are 24VAC power and the RS485 Comms link. Locations of electrical terminals are
shown in Figure 3-17, which is a rear view of the module.
When all connections have been made, protect the module from dirt and moisture by covering it with
plastic but do not mount the module in the wall plate until commissioning is completed. This is to
allow addresses to be set as part of the commissioning process.
Figure 3-17: GENII CSFCAH REM Control Station Fan Control, A/H Module
- INSTALLATION INSTRUCTIONS 1
- Proprietary 2
- Trademark 2
- Disclaimer 2
- Document Management 3
- Document Title: 3
- Revision History 3
- Contents 5
- Contents (Continued) 6
- List of Illustrations 8
- List of Tables 10
- Chapter 1 - Preliminary 11
- Information 11
- 1-1 Introduction 12
- Table 1-1: Document Chapters 13
- 1-2 Special Considerations 14
- 1-3 Unpacking Instructions 14
- 1-4 Installation Plans 14
- 1-5 Tools and Test Equipment 14
- Chapter 2 - Mechanical 15
- 2-1 Introduction 16
- 2-2 Physical Descriptions 16
- Mounting Hole 17
- Typical of 8 17
- GENESIS MPC 19
- GENESI S 20
- ANALOG INPUT 20
- DO 1 DO 2 DO 3 23
- MOUNTING 25
- 2-3.1 DIN Rails 26
- Side View 28
- Top View 28
- 90 Degrees 28
- 2-4 Dierence Data 29
- Chapter 3 - Electrical 31
- 3-1 Introduction 32
- 3-4.1 REM Power Connections 50
- 3-4.2 REM Comms Connections 51
- DIGI TA L OUTPUT 56
- Remote Expansion Modul e 56
- ISOLA TED DIGI TA LINPUT 57
- PULSE INPUT 58
- 24V AC or DC Supply 64
- 0V AC or DC Supply 64
- C ON TROL S YSTEMS 66
- USTRALIA 66
- Chapter 4 75
- Commissioning 75
- 4-1 Introduction 76
- JUMPER WIRE 81
- SWITCH CLOSED 83
- SWITCH OPEN 83
- GENII DI REM 83
- EXTERNAL 85
- GENESIS II DDCINNOTECH 87
- 4-1.3 Install AISCs 90
- 4-1.4 Set Jumper Plugs 91
- AI 5 A I6 AI7 AI8 AI 9 92
- RS485 COMMS 93
- CONNECTIONS 93
- END-OF-CABLE 93
- GEINNOTECH 94
- 4-1.6 Initial Tests 97
- 4-1.7 Final System Check 99
- Chapter 5 - Network 101
- Installation 101
- 5-1 Overview 102
- 5-2 Genesis II Products 102
- 5-2.1 Definitions 103
- 5-3 Installation 104
- 5-3.3 Wiring Topology 105
- Zone A Zone B 107
- Zone BZone A 107
- Repeater 108
- Page 109 109
- - - - - 111
- Page 113 113
- Building A 115
- Building B 115
- DANGEROUS EARTH CONNECTION! 117
- NOT TO BE USED! 117
- Page 119 119
- Page 121 121
- MPI With Isolated RS485 122
- Isolated from 123
- Connected to 123
- Innotech Support 124
Dell Precision T7500 manuály
Uživatelské manuály a uživatelské příručky pro Počítače Dell Precision T7500.
Poskytujeme 2 manuály pdf Dell Precision T7500 ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comments to this Manuals